xp 1700+ @ 2700MHz wc - Page 2

26th September 2003, 23:19

that's a big no

read somewhere it wasn't nessesary

i'll try to run the pc at low voltages and see if the 12V line increases

26th September 2003, 23:24

well, maybe not nessesary but it certainly won't do harm. I don't think Abit equiped it's latest mobo with active cooling just for fun.

You can still raise the volt of your rams a bit.

jmke · 27th September 2003, 00:00

Quote:

Originally posted by Tarantula
does someone here know how to resolve this prob?

/me strijk

.. solution: overclock less :grin:

27th September 2003, 00:04

pestkop

27th September 2003, 01:26

Cool your MOSFETS, at least place a fan above them blowing over. Or better put a good HS on them.
It will stabilize your Vcore, Vdimm and other derived voltages. And at the same time reduce the drain on your 12V line.

27th September 2003, 10:01

hmmm, my Vcore is idd not so stable, when @ 1.74 Vcore it always gives between 7,0 and 7,4Vcore

now running @ 2200MHz @ 1.47Vcore and the 12 V line went up to 11.80

got a hs laying arround, maybe one of these days gonna cut it up in little hsinks

27th September 2003, 10:21

screw your psu open and see if you have a rheostat in there, if yess try to increase it

greetz

27th September 2003, 10:32

I'll need to screw it open annyway because it's too noisy

so I'll check if there is one

29th September 2003, 16:30

apparently for some reason, my FSB isn't stable annymore, it's stable at 200, but when put at 213 or 217, it sometimes drops a few mhz and then regains the speed again, in the past it was stable 217 FSB I tested, strange it's not so stable annymore when the weather is much better for ocking :grum:

16th October 2003, 20:55

hi tarantula ,

nice o/c , for your psu , there is the vmod , ( no pot inside )
http://forum.hardware.fr/forum2.php3...sh=&subcat=120 , it's in french but you can take the original link from pctuner and make the traduction from italian to english .

hope to have help you , kind regards , tomati .

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FireGL V5600 vs. QuadroFX 1700 vs. FireGL V3600	jmke	WebNews	0	7th February 2008 10:47

26th September 2003, 23:19	#11
Tarantula Posts: n/a	that's a big no read somewhere it wasn't nessesary i'll try to run the pc at low voltages and see if the 12V line increases

26th September 2003, 23:24	#12
PlayboY Posts: n/a	well, maybe not nessesary but it certainly won't do harm. I don't think Abit equiped it's latest mobo with active cooling just for fun. You can still raise the volt of your rams a bit.

27th September 2003, 01:26	#15
FreeStyler Posts: n/a	Cool your MOSFETS, at least place a fan above them blowing over. Or better put a good HS on them. It will stabilize your Vcore, Vdimm and other derived voltages. And at the same time reduce the drain on your 12V line.

27th September 2003, 10:01	#16
Tarantula Posts: n/a	hmmm, my Vcore is idd not so stable, when @ 1.74 Vcore it always gives between 7,0 and 7,4Vcore now running @ 2200MHz @ 1.47Vcore and the 12 V line went up to 11.80 got a hs laying arround, maybe one of these days gonna cut it up in little hsinks

27th September 2003, 10:21	#17
Da_BoKa Posts: n/a	screw your psu open and see if you have a rheostat in there, if yess try to increase it greetz

27th September 2003, 10:32	#18
Tarantula Posts: n/a	I'll need to screw it open annyway because it's too noisy so I'll check if there is one

29th September 2003, 16:30	#19
Tarantula Posts: n/a	apparently for some reason, my FSB isn't stable annymore, it's stable at 200, but when put at 213 or 217, it sometimes drops a few mhz and then regains the speed again, in the past it was stable 217 FSB I tested, strange it's not so stable annymore when the weather is much better for ocking :grum:

16th October 2003, 20:55	#20
tomati Posts: n/a	hi tarantula , nice o/c , for your psu , there is the vmod , ( no pot inside ) http://forum.hardware.fr/forum2.php3...sh=&subcat=120 , it's in french but you can take the original link from pctuner and make the traduction from italian to english . hope to have help you , kind regards , tomati .