Shuttle XPC slim DS50U7 Barebone Review

Others/All-in-one PC by stefan @ 2024-11-03

The DS50U7 barebone from Shuttle did impress us in terms of performance, considering we are talking about a fanless design. PL1 is limited to 15W, while PL2 is limited to 17W, while in the case of the ECS LIVA Z5 Plus with active cooling and the i5-1335U SoC, we noted PL1 set at 20W and PL2 set at 39W, which is considerably higher; despite that, we see the i7-1355U winning in some cases, due to the implementation of DDR5 memory, higher boost on the iGPU clock, more execution units, but also a higher boost on the CPU, helping quite a bit in low to medium loads, a situation which is frequently found when using the device like 90% of the time.

  • prev
  • next

Product Specifications

Fanless and Silent

Passive cooling, no fan noise at all

Perfect to be used in noise-sensitive environments

Fanless, dust-free and thus virtually maintenance-free

 

24/7 Nonstop Operation

This device is approved for 24/7 permanent operation.

Requirements:

- Free circulation of air amongst the PC must be guaranteed.

- Ventilation holes must stay clear.

- If a hard disk is installed, this must also be approved for permanent operation by its manufacturer

 

Chassis

Slim-PC with black steel chassis

Without cooling fan, passive cooling only

The bay for memory modules, 2.5" drive and M.2 cards can easily be accessed

by removing the bottom chassis cover.

Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres

Weight: 1.6 kg net and 2.3 kg gross

Two holes for Kensington Lock and numerous

threaded holes (M3) at both sides of the chassis

 

Operating Position

1) Vertical: Usual operating position with the supplied feet (DisplayPort output facing up).

2) VESA-mounted: The device can also be mounted behind an appropriate monitor using the supplied VESA mount kit.

 

Operating System

This barebone system comes without operating system.

It is compatible with Windows 10/11 (64-bit) and Linux (64-bit).

 

Processor

Model: Intel Core i7-1355U

Code name: Raptor Lake-U (13th generation Intel Core)

Performance-cores (P-Cores): 2 cores (4 threads), Basic/Turbo clock: 1.7-5.0 GHz

Efficient-cores (E-Cores): 8 cores (8 threads), Basic/Turbo clock: 1.2-3.7 GHz

Smart-Cache (L3): 12 MB

Base Power (PL1 TDP): max. 15 W

Maximum Tjunction Temperature: 100 °C

System-on-a-chip architecture (SoC) with integrated memory and graphics controller

BGA1700 package - directly soldered onto the mainboard

Lithography: Intel 7 process (10 nm Enhanced SuperFin)

 

Integrated Graphics

Intel UHD Graphics

GPU clock frequency: max. 1300 MHz

Execution Units (EUs): 96

Supports up to three independent screens:

1) DisplayPort 1.4 supports Ultra HD @ 60 Hz

2) HDMI 2.0b supports Ultra HD @ 60 Hz

3) D-Sub/VGA supports analog displays

 

Mainboard / BIOS

Proprietary Mainboard for the Shuttle DS50U series

Supports resume after power failure

Supports Wake on LAN (WOL)

Supports Power on by RTC Alarm

Supports boot from M.2 SSD cards und USB devices

AMI BIOS in 32 MByte EEPROM with SPI interface

Supports hardware monitoring and Watchdog function

Supports Unified Extensible Firmware Interface (UEFI)

Supports Firmware-TPM (fTPM) Version 2.0

 

Power Adapter

External 90 W power adapter (fanless)

Input: 100~240 V AC, 50/60 Hz, max. 1.6 A

Output: 19 V DC, max. 4.74 A, max. 90 W

DC cable length: ca. 170 cm

AC cable length: ca. 170 cm (3-pin Micky MM C6 and Schuko earthed safety plug)

 

DC Input connector

DC Input Connector: 5.5 / 2.5 mm (outer/inner diameter)

The DC-input of the computer supports an external

power source with either 12V +/- 5% or 19V +/- 5%.

 

Memory support

2x SO-DIMM slot with 262 pins

Supports DDR5-5200 (PC5-41600) SDRAM at 1.1 V

Supports memory modules with higher frequency rating

Supports Dual Channel mode

Supports a maximum of 32 GB per DIMM,

maximum total size: 64 GB

Supports two unbuffered DIMM modules (no ECC or registered)

Two thermal pads for the RAM modules are included

 

2.5" Drive Bay with SATA connector

Supports one Serial ATA hard disk

or one SATA SSD drive in 6.35 cm / 2.5" format

Device height: max. 9.5 mm

Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth

Supports Unified Extensible Firmware Interface (UEFI)

Note: no Serial ATA cable is required.

 

Two M.2-2280 Slots for SSD cards

This product features two M.2-2280 Key-M slots

- it supports M.2 cards with a width of 22 mm and a length of 80 mm (type 2280)

- one M.2 SSD card with PCIe/NVMe interface is supported

- the second M.2 SSD card must have SATA interface

- the second slot can also be used for the optional WWN04 kit to support a 4G/5G wireless network card

 

M.2 slot for WLAN cards

Slot: M.2-2230 Type E

Interfaces: PCI-Express Gen. 3.0 X1 und USB 2.0

Supports M.2 cards with a width of 22 mm and a length of 30 mm (type 2230)

Two antenna cables are pre-installed.

A WLAN expansion card in M.2-2230 format and two WLAN antennas are required for the WLAN function.

Optional Shuttle accessory: WLN-M1

 

Audio

Audio Realtek® ALC888S High-Definition Audio

Two analog audio connectors (3.5 mm) at the front panel:

1) 2 channel line out (headphones)

2) microphone input

Digital multi-channel audio output: via HDMI and DisplayPort

 

Dual LAN (2.5G + 1G)

Dual network with two RJ45 ports

Used network chips:

1) left: Intel i219 Ethernet Controller supports 1.000 / 100 / 10 Mbps operation

2) right: Intel i226 Ethernet Controller supports 2.500 / 1.000 / 100 Mbps operation

Supports WAKE ON LAN (WOL)

Supports network boot by Preboot eXecution Environment (PXE)

 

Front Panel connectors/buttons

4x USB 3.2 Gen 1 (max. 5 Gbps, blue)

2x USB 3.2 Gen 2 (max. 10 Gbps, red)

Microphone input

Audio Line-out (headphones)

Power button

Power LED (blue)

HDD LED (yellow)

 

Back Panel connectors

DisplayPort 1.4

HDMI 2.0b

D-Sub/VGA

2x USB 2.0 (black)

2x Intel RJ45 LAN (left: 1 Gbps and right: 2.5 Gbps)

Serial COM port (5V / 12V, switchable to RS232 / RS422 / RS485)

DC-input connector for external power adapter

4-pin connector (2.54 mm pitch) for power button, Clear CMOS and 5 V DC

2x connector for external WLAN antennas

 

Always-On Jumper

By removing Jumper JP1 (please refer to the quick user guide),

the system will start unconditionally once power is applied.

 

Scope of Delivery

Multi-language user guide

Two metal feet with four screws M3 x 7 mm

VESA mount for 75/100mm standard (two metal brackets)

Four screws M3 x 7 mm (screws together VESA mount and PC)

Four screws M4 x 10 mm (to fix the VESA mount to the external surface)

Two screws M3 x 5 mm to mount a 2.5" storage in the bay

Two screws M3 x 5 mm to mount M.2 cards

4x Thermal Pad for cooling of optional components:

- 2x for M.2 SSD cards (ca. 70 x 20 x 4 mm)

- 2x for RAM modules (ca. 50 x 15 x 2 mm and 60 x 20 x 1 mm)

Driver DVD for Windows

External 90W power adapter with power cord (with protective-earth contacts)

 

Optional Accessories

- PCP11: adapter cable for the second COM port (replaces the VGA port)

- CXP01: adapter cable for external power button

- WLN-M1: WLAN module (supports WLAN/Bluetooth) with two external antennas and cables

- PRM01: 2U rack mount front plate for two Shuttle XPC slim

- DIR01: mounting kit for 35 mm DIN-Rail

- WWN04: 4G/5G kit with antennas - enables the use of an optional 4G/5G card in M.2 format and a nano SIM card

 

Environmental Specifications

Operating temperature range: 0~40 °C [5]

Relative humidity, non-condensing: 10~90 %

 

  • prev
  • next

No comments available.

 

reply